Steuerung der Ventilantriebe S 6/-12/-16
25
Für die Einstellungen der Schnittstelle gilt:
9600 baud
8
bit
1 start bit
1
stop-bit
Tabelle 7 Tabelle der Kommandos
Kommando
Aktion
Bemerkung
1,2,3,...,6
(..,15,16,01,..)
Ventil fährt in die eingegebene Position
nur 360°-Ventile
H,h
Ventil fährt in die HOME-Position (Pos.1)
nur 360°-Ventil
L,l
Ventil fährt in die LOAD-Position
nur L/I-Ventile
I,i
Ventil fährt in die INJECT-Position
nur L/I-Ventile
V,v
Ausgabe der Programmversion
P,p
Ausgabe der aktuellen Position
T,t
Ausgabe des Ventiltyps
Parallel zur Steuerung über die RS-232 Schnittstelle kann der Anschluss OUT der
WAGO Anschlussleiste zur Schaltung anderer Geräte genutzt werden. Bezüglich
der Aktivierung des Ausganges gelten die gleichen Bedingungen wie beim
manuellen Betrieb. Sind auch die Anschlüsse HOME, INJ. und/oder LOAD an das
System angeschlossen, haben die RS-232 Anschlüsse Priorität.
Fernsteuerung über die Wago-Leiste
Generell gilt, dass die Anschlüsse der WAGO-Leiste als Open Collector (OC)
ausgelegt sind, weshalb die Polung von Eingängen zwingend beachtet werden
muss.
Ventile mit 2 Schaltpositionen
Der HOME Eingang ist bei diesen Ventilen inaktiv. Wenn der LOAD Eingang mit
GROUND kurzgeschlossen wird, ist zur Steuerung nur eine Verbindung von INJ.
und GROUND mit dem signalgebenden Gerät
(z.B. Interface Box) erforderlich.
Liegt an INJ. kein Signal an befindet sich das Ventil aufgrund des LOAD
GROUND Kurzschlusses in der LOAD Position. Erhält der INJ. Eingang
ebenfalls ein Kurzschlusssignal, erfolgt die Schaltung in die INJECT
Position. INJ. hat gegenüber LOAD die Priorität.
360° Ventile mit 6, 12 oder 16 Schaltpositionen
Nur die 360° Ventile können über die WAGO-Leiste alternativ im analog oder binär
Modus betrieben werden. Die jeweils zugehörige Kombination der DIP-
Schalterstellungen entnehmen Sie bitte der Tabelle auf Seite 23.
Steuerung im analog Modus
Für die Steuerung anderer Geräte über OUT-Signale gilt wiederum, dass der
Ausgang aktiv ist, wenn sich das Ventil in der HOME Position (=Position 1)
befindet. In den Positionen 2-6, 2-12 bzw. 2-16 ist der Ausgang inaktiv.
Für eingehende Schaltbefehle stehen drei Eingänge zur Verfügung. Über HOME
wird das Ventil in die Position 1 gefahren. Während über BACKW./INJ. das Ventil
eine Position zurück gesetzt wird, erfolgt über FORW./LOAD ein Schalten in
entgegengesetzter Richtung. Zum Weiterschalten in gleicher Richtung (ab- oder
aufwärts) muss ein anliegendes Dauersignal entsprechend einer Impulsschaltung
kurzzeitig unterbrochen werden.
Содержание Smartline S12
Страница 2: ......