Knauer Azura Assistant ASM 2.1L Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 35

Knauer Azura Assistant ASM 2.1L Скачать руководство пользователя страница 22

ASM 2.1L user manual V6815

Functionality tests

22

Result

The firmware is successfully initialized if shortly after switching on the
device all three LEDs light up for approx. 1 second. If the test fails an error
message will be displayed. Contact the Technical Support of KNAUER if
the error occurs several times.

Functionality tests

Installation Qualification

(IQ)

The customer may request the Installation Qualification, which is free of
charge. In case of a request, the Technical Support of KNAUER or from a
provider authorized by KNAUER performs this functionality test during
the installation.
The Installation Qualification is a standardized document that comes as
part of the delivery and includes the following:



confirmation of flawless condition at delivery



check if the delivery is complete



certification on the functionality of the device

Operation Qualification

(OQ)

The Operation Qualification includes an extensive functionality test
according to KNAUER standard OQ documents. The Operation Qualifica-
tion is a standardized document and free of charge. It is not part of the
delivery, please contact the Technical Support in case of request.
The Operation Qualification includes the following:



definition of customer requirements and acceptance terms



documentation on device specifications



device functionality check at installation site

Test Intervals

To make sure that the device operates within the specified range, you
should test the device regularly. The test intervals are dependent on the
usage of the device.

Execution

The test can be carried out either by the Technical Support of KNAUER or
from a provider authorized by KNAUER (for a fee).

Troubleshooting

First measures

1. Check all cabling.
2. Check all screw fittings.
3. Check whether air has gotten into the supply lines.
4. Check device for leaks.
5. Pay attention to system messages.

Further measures

Inform the Technical Support of KNAUER.

Procedure

Process

Figure

1. Switch on the device at the

power switch

1

on the rear

side.

2. Wait until the device has com-

pleted the self-test.

3. If the self-test has been suc-

cessfully completed, the LED

2

on the right lights up green.

Fig. 11

Power switch on the rear
side of the device

1

«
...
20
21
22
23
24
...
»

Содержание Azura Assistant ASM 2.1L




































Отзывы:

Нет отзывов