background image

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

802725

20

Earthing Instructions

The dryer must be earthed. In the event of malfunction 

or breakdown, earthing will reduce the risk of electric 

shock by providing a path of least resistance for 

electric current. The dryer is equipped with a cord 

having an equipment-earthing conductor and a 3 prong 

earthing plug. The plug must be plugged into an 

appropriate outlet that is properly installed and earthed 

in accordance with local codes and ordinances.
Do not modify the plug provided with the dryer – if it 

will not fit the outlet, have a proper outlet installed by 

a qualified electrician.

If the electrical supply does not meet the above 

specifications and/or you are not sure your building 

has an effective earth, have a qualified electrician or 

your local electrical utility company check it and 

correct any problems.

Step 11: Recheck steps 1-10

Refer to 

Installer Checklist

 on the back cover of this 

manual and make sure that unit is installed correctly.
Run washer through one complete cycle to make sure 

it is operating properly.

Improper connection of the equipment-
earthing conductor can result in a risk of 
electric shock. Check with a qualified 
electrician or serviceman if you are in doubt 
as to whether the dryer is properly earthed.

W159

WARNING

Содержание LTKA6

























Отзывы: