manualshive.com logo in svg

KitchenAid KUDD03DT, Техническое образование

Поделиться
Скачать
KitchenAid KUDD03DT Скачать руководство пользователя страница 61

5-5

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

WARNING

LIMIT THERMOSTAT

Refer to page 4-9 for procedure for servicing 

the limit thermostat.
1.   Unplug dishwasher or disconnect power.
2.  Disconnect the wire connectors from the 

limit thermostat terminals. Set the ohm-

meter to the R x 1 scale.

4.  Touch the ohmmeter test leads to the limit 

thermostat  terminals.  The  meter  should 

indicate  continiuity  @  149

°

F  (65

°

C)  and 

open @ 170

°

F (76.7

°

C)

High Limit 

Terminals

THERMAL FUSE

Refer to page 4-9 for procedure for servicing 

the thermal fuse.
1.   Unplug dishwasher or disconnect power.
2.  Disconnect the wire connectors from the 

thermal fuse terminals. Set the ohmmeter 

to the R x 1 scale.

4.  Touch  the  ohmmeter  test  leads  to  the 

thermal fuse terminals. The meter should 

indicate open @ 190

°

F (87.7

°

C)

Thermal Fuse 

Terminals

Содержание KUDD03DT







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды