manualshive.com logo in svg

KitchenAid KUDD03DT, Техническое образование

Поделиться
Скачать
KitchenAid KUDD03DT Скачать руководство пользователя страница 51

4-15

CABINET - MOUNTED COMPONENTS

REMOVING THE LINE BREAK, TUB LID, AND SLIDER ASSEMBLIES

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.

WARNING

1.  Unplug dishwasher or disconnect power.
2.  Turn off the water supply to the dishwasher. 
3. 

To remove the line break:

 

a) Remove the drawer from the unit.
b) Disconnect the wiring connectors from 

the line break terminals.

c)  Loosen  the  screw  and  slide  the  line 

break out of the holder.

4. 

To  remove  the  tub  lid  and  slider  as-

semblies:

 

a) Lift the tab at the bottom of each slider.

Wiring Connectors

 Line Break

 Tab

 Slider

 Screw

b) Pull the sliders down to release them and 

remove the sliders from the cabinet.

 

NOTE:

 The left and right lid slider assem-

blies are marked “LEFT” and “RIGHT.”

c)  Push the wiring harness and hose as-

sembly  back  out  of  the  way  so  that 

you  can  lower  the  left  side  of  the  lid 

assembly.

Wiring Harness & Hose

Continued on the next page.

Содержание KUDD03DT







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды