manualshive.com logo in svg

KitchenAid KUDD03DT, Техническое образование

Поделиться
Скачать
KitchenAid KUDD03DT Скачать руководство пользователя страница 60

5-4

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

WARNING

Drain Solenoid

Refer to page 4-8 for procedure for servicing 

the drain solenoid.
1.   Unplug dishwasher or disconnect power.
2.  Disconnect  the  wire  connectors  from 

the  DRAIN  solenoid  terminals  on  drain 

solenoid. Set the ohmmeter to the R x 1 

scale.

4.  Touch the ohmmeter test leads to drain 

solenoid terminals. The meter should in-

dicate approximately 19

Ω

.

Solenoid Terminals

INLET FILL VALVE

Refer to page 4-16 for procedure for servicing 

the inlet fill valve.

1.   Unplug dishwasher or disconnect power.
2.  Disconnect the wire connectors from the 

upper and lower Inlet fill 

 solenoid terminals. 

Set the ohmmeter to the R x 1 scale.

4.  Touch the ohmmeter test leads to the up-

per and lower Inlet fill solenoid terminals. 

The meter should indicate approximately 

1.1k

Ω

.

Solenoid 

Terminals

Lower (2)

Upper (2)

Содержание KUDD03DT







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды