KitchenAid KUDD03DT Скачать руководство пользователя страница 13

Страница: 13 / 70

2-1

INSTALLATION INFORMATION

INSTALLATION REQUIREMENTS FOR DOUBLE DRAWER

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

When using the dishwasher, fol-

low basic precautions, including the

following:

Read all instructions before using the dish-

•

washer.
Use the dishwasher only for its intended

•

function.
Use only detergents or rinse agents recom-

•

mended for use in a dishwasher, and keep

them out of the reach of children.
When loading items to be washed:

•

1) Locate sharp items so that they are not

likely to damage the door seal; and

2) Load sharp knives with the handles up to

reduce the risk of cut-type injuries.

Do not wash plastic items unless they are

•

marked “dishwasher safe” or the equivalent.

For plastic items not so marked, check the

manufacturer's recommendations.
Do not touch the heating element during or

•

immediately after use.
Do not operate the dishwasher unless all

•

enclosure panels are properly in place.
Do not tamper with controls.

•

Do not abuse, sit on, or stand on the door,

•

lid, or dish racks of the dishwasher.
To reduce the risk of injury, do not allow chil-

•

dren to play in or on the dishwasher.
Under certain conditions, hydrogen gas may

•

be produced in a hot water system that has

not been used for two weeks or more. HY-

DROGEN GAS IS EXPLOSIVE. If the hot

water system has not been used for such a

period, before using the dishwasher turn on all

hot water faucets and let the water flow from

each for several minutes. This will release

any accumulated hydrogen gas. As the gas

is flammable, do not smoke or use an open

flame during this time.

Remove the door or lid to the washing

•

compartment when removing an old dish-

washer from service or discarding it.

Tip Over Hazard

Do not open dishwasher drawer until

inside cabinet opening.
Doing so can cause serious injury.

WARNING

You need to:

Slowly open dishwasher drawer while some-

•

one grasps the rear of the dishwasher. Re-

move shipping materials. Close dishwasher

drawer. Latch the dishwasher drawer shut.
Observe all governing codes and ordi-

•

nances.

Install this dishwasher as specified in these

•

instructions.
Have everything you need to properly install

•

dishwasher.

Contact a qualified installer to ensure that

•

dishwasher is installed to meet all electrical

and plumbing national and local codes and

ordinances.

Содержание KUDD03DT







































































Результаты поиска

Содержание KUDD03DT

Отзывы:

Бренды по названию

Популярные бренды

KitchenAid KUDD03DT, Техническое образование

Результаты поиска

Содержание KUDD03DT

Отзывы:

Бренды по названию

Популярные бренды