KitchenAid KUDD03DT Скачать руководство пользователя страница 5

Страница: 5 / 70

1-1

GENERAL

DISHWASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on the appliance.

Always read and obey all safety messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word

“DANGER” or “WARNING.” These words mean:

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance

of injury, and tell you what can happen if the instructions are not followed.

You can be killed or seriously injured if you don’t

immediately follow instructions.

You can be killed or seriously injured if you don’t

follow instructions.

DANGER

WARNING

Содержание KUDD03DT







































































Результаты поиска

Содержание KUDD03DT

Отзывы:

Бренды по названию

Популярные бренды

KitchenAid KUDD03DT, Техническое образование

Результаты поиска

Содержание KUDD03DT

Отзывы:

Бренды по названию

Популярные бренды