KitchenAid KUDD03DT Скачать руководство пользователя страница 49

Страница: 49 / 70

4-13

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.

WARNING

1. Unplug dishwasher or disconnect power.
2. Turn off the water supply to the dish-

washer.

3. Remove the tub and bottom cover (see

pages 4-6 & 4-7).

4. Remove the front panel, intermediate

panel, and control housing (see “Remov-

ing The Front Panel, Intermediate Panel,

And The Control Housing,” page 4-11).

5. Remove the inlet and outlet bezels (see

page 4-5).

To remove the pressure switch:

a) Disconnect the wire connectors from

the pressure switch terminals.

b) Remove the retaining screw from the

pressure switch.

c) Disconnect the hose clamp and the

hose from the pressure switch.

REMOVING THE PRESSURE SWITCH, DETERGENT DISPENSER,

MAIN CONTROL MODULE, AND DRY FAN

To remove the detergent dispenser:

a) Disconnect the wire connectors from

the dispenser solenoid and Rinse Aid

sensor.

b) Remove the four screws and two re-

taining brackets from the detergent

dispenser, and remove the dispenser.

Pressure Switch Wire Connectors

Screw

Hose

Detergent Dispenser

Wire Connectors

TUB FRONT COMPONENTS

Rinse Aid

Sensor

Retaining Brackets & Screws

Continued on the next page.

Содержание KUDD03DT







































































Результаты поиска

Содержание KUDD03DT

Отзывы:

Бренды по названию

Популярные бренды

KitchenAid KUDD03DT, Техническое образование

Результаты поиска

Содержание KUDD03DT

Отзывы:

Бренды по названию

Популярные бренды