KitchenAid KUDD03DT Скачать руководство пользователя страница 57

Страница: 57 / 70

5-1

COMPONENT TESTING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

WARNING

DISHWASHER COMPONENTS

Check all connections before replacing com-

•

ponents, looking for broken or loose wires,

failed terminals, or wires not pressed into

connectors far enough.
Voltage checks must be made with all con-

•

nectors attached to the boards.
Resistance checks must be made with power

•

cord unplugged from outlet, and with wiring

harness or connectors disconnected.

Before testing any of the components,

perform the following checks:

The most common cause for control failure

•

is corrosion on connectors. Therefore, dis-

connecting and reconnecting wires will be

necessary throughout test procedures.
All tests/checks should be made with a VOM

•

or DVM having a sensitivity of 20,000 ohms-

per-volt DC, or greater.

FAN MOTOR

Refer to page 4-13 for procedure for servicing

the fan motor.
1. Unplug dishwasher or disconnect power.
2. Disconnect the wire connectors from the

FAN MOTOR terminals on fan motor.

3. Set the ohmmeter to the R x 1 scale.
4. Touch the ohmmeter test leads to fan mo-

tor terminals. The meter should indicate

approximately 79

Fan Motor Terminals

Содержание KUDD03DT







































































Результаты поиска

Содержание KUDD03DT

Отзывы:

Бренды по названию

Популярные бренды

KitchenAid KUDD03DT, Техническое образование

Результаты поиска

Содержание KUDD03DT

Отзывы:

Бренды по названию

Популярные бренды