Kitagawa MR250RAE13 Скачать руководство пользователя страница 36

Страница: 36 / 50

Symptom

②：

Table does not rotate but generates a noise

Possible causes

Corrective actions

Motor makes a howling sound to try to
rotate

→

Seizure of gears due to lack or
deterioration of lubricating oil

Stop the use of NC rotary table
immediately.
Please contact the sales agent.

Gears generate a noise

→

Faulty rotation due to damaged

gears

Stop the use of NC rotary table
immediately.
Please contact the sales agent.

Unit generates a noise at startup and
stops soon

→

Faulty rotation because foreign
substances mix in the oil bath

Supply lubricating oil until foreign
substances come out of the drain port.

Symptom

③：

Table does not rotate smoothly but generates a noise

Possible causes

Corrective actions

Noise is generated repeatedly during
rotation

→

Gears are damaged

Stop the use of NC rotary table
immediately.

Please contact the sales agent.

→

Faulty rotation of gears because
foreign substances mix in the oil
bath

Open the lubricating oil drain port, and
supply lubricating oil until foreign
substances come out of the drain port.

Load due to overloading exceeds motor
output

Compare the specification of NC rotary
table with the work condition to make
improvement

Lack or deterioration of lubricating oil
blocks smooth rotation

Check oil level, viscosity and change
interval of lubricating oil

Faulty clamp device

See “Symptom

⑤

”

Inappropriate backlash amount

Adjust backlash amount to appropriate
value

Symptom

④：

Chattering occurs during cutting

Possible causes

Corrective actions

Inappropriate clamp condition of NC
rotary table or fixture

Check the clamp condition, and correct it

Excess cutting force is applied during
cutting

Adjust cutting condition to the specified
condition to change the cutting force to
appropriate value

Faulty clamp device

See “Symptom

⑤

”

Faulty locking of worm spindle in the
backlash adjustment

Readjust

Fault due to damaged NC rotary table or
expired life of components

Stop the use of NC rotary table
immediately.
Please contact the sales agent.

Fault occurs only during continuous
cutting

→

Lack or deterioration of lubricating
oil blocks smooth rotation

→

Inappropriate backlash amount

Check oil level, viscosity and date of last
change of lubricating oil
Adjust backlash amount to appropriate
value

Chips accumulate in rotary part of NC
rotary table

Remove accumulated chips in daily
inspection

Содержание MR250RAE13



















































Результаты поиска

Содержание MR250RAE13

Отзывы:

Бренды по названию

Популярные бренды

Kitagawa MR250RAE13, Инструкция по эксплуатации

Результаты поиска

Содержание MR250RAE13

Отзывы:

Бренды по названию

Популярные бренды