Kitagawa MR250RAE13 Скачать руководство пользователя

Страница: 33 / 50

12. Motor Cover

12-1. Dismount

Please follow the procedure below for removing the motor cover. [See Fig.5]

1) Loosen the hexagon socket head cap screws

⑪

, which set the motor case

①

on the

base

⑩

and carefully detach the motor case

①

by lifting the case upward. On this

occasion, since wiring and air hose, etc. are connected, be careful not to apply load to

them in consideration of the their length.

2) Remove wiring, air hose and cannon connector of motor

②．

12-2. Waterproofing

In order to prevent the entering of coolant from the outside, O-ring

④

is used at the portion

of connection between motor case

①

and the body.

For detaching the motor, remove either of the hexagon

socket headless tapered pipe plug,

⑤

⑥

, and loosen

the hexagon socket head cap screw

⑦

on the coupling

⑧

which connects the worm shaft

⑨

and the motor

②

Then, remove the four hexagon socket head cap screws

③

which secure the motor

②

in order to detach the motor.

When re-installing the motor

②

, be sure to securely

tighten the bolts and plugs.

When the motor case

①

is re-installed, be carefully not to

damage the O-ring. The damaged O-ring may allow the

cutting water to enter the motor case.

CAUTION

Содержание MR250RAE13



















































Результаты поиска

Содержание MR250RAE13

Отзывы:

Похожие инструкции для MR250RAE13

Бренды по названию

Популярные бренды

Kitagawa MR250RAE13, Инструкция по эксплуатации

Результаты поиска

Содержание MR250RAE13

Отзывы:

Похожие инструкции для MR250RAE13

Бренды по названию

Популярные бренды