manualshive.com logo in svg

Kitagawa MR250RAE13, Инструкция по эксплуатации

Поделиться
Скачать
Kitagawa MR250RAE13 Скачать руководство пользователя страница 25

19 

NOTICE 

NOTICE 

9. Maintenance Work 

9-1. Corrective Action in Case of Failure, and Disassembly 

See the “Troubleshooting” if a failure occurred in the unit due to any reason. Also, for the 

disassembly procedure when performing the maintenance work, refer to the parts list and 

the procedure given in the corresponding maintenance item. 

 

9-2. Before Performing Maintenance Work 

When performing the maintenance work, shut off the power (primary power supply) of the 

machining center or Kitagawa’s own controller to set the pressure adjusting valve of air 

combination that supplies the air to the NC rotary table to 0 MPa or shut off the power of the 

air compressor to exhaust the compressed air, so as to stop the supply of the working fluid. 

 

Perform the maintenance work with the workpiece 

removed. Performing the work with the workpiece left on 

the table may cause the workpiece to be dropped out, 

resulting in injuries. 

 

Appropriate value in each maintenance item has been set 

for smooth function of each device, and thus you should 

observe it. Performing the maintenance work without 

observing the appropriate value may cause NC rotary table 

to fail or each device to be damaged. 

 

Clamp the table clamp device of NC rotary table when 

removing the workpiece. 

 

 

 

 

CAUTION 

Содержание MR250RAE13



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды