KISANKRAFT KK-TH-525 Скачать руководство пользователя страница 10

Страница: 10 / 44

KisanKraft

Tea-Leaf Harvester

KK-TH-525 / KK-TH4-34



: www.kisankraft.com



: [email protected]



: +91.80. 22178200

Page 10 of 44

8. Cleaning of the carbon in the spark plug and the adjustment of the space: After

every 25 hours of working, please take off the spark plug and clean it. Adjust the

space between the electrodes (0.5-0.6mm)

9. Dismantle the air filter after 15 hours of usage. Use the gas line to clean it

thoroughly. Then dry and reinstall it. Dismantle the casing lid, clean the carbon

and the dirt.

10. Cleaning of carburetor. When working in bad conditions, carbon powder and dust

on the tree may contaminate the machine, so besides cleanings after each

usage, cleaning after every 100 hours usage is necessary. (Cleanings must be

held when the oil box is switched off.) (Note: The inside parts have matched the

machine, please do not adjust it.)

11. Do not use for a long time, without allowing to cool or clean the machine

12. When the machine is cooled off, let the fuel go out and press the oil pump so the

fuel remaining in the pump goes back to the oil tank. At last, empty the fuel in

the oil tank.

13. Take off the spark plug, and drop the oil into the hole. Pull the starter so that the

oil covers the inner well. Put the spark plug back.

14. Clean the outside parts, blades and blade edges of the machine. Put it in a dry

room.

NOTE

: Necessary repairs must be done by the authorized dealer.

TROUBLESHOOTING

STARTING PROBLEMS

Symptom

Category

Cause

Remedy

Lighting a

fire

without a

spark.

Spark plug

The electrodes are damped.

Drying

Carbon got deposited in the

electrodes of the spark plug.

Cleaning

The ramous insulator of the

electrode is bad.

Replacing

the

spark plug

The space between electrodes is

too small or too large.

Adjust it to

0.5 -0.6mm

The electrodes are overheated

Replacing

the

spark plug

Lighting a

fire with a

spark.

Good

Compression

High density of the fuel

Adjusting

carburetor

Bad quality of the fuel

Use better fuel

Bad

compression

The casing piston and the piston

ring have been badly damaged due

to wear and tear.

Replacing

the

piston ring or

piston whichever

is necessary

Carburetor

Lack of fuel

Fill the fuel

Measuring hole jammed

Clearing

Cleaner-net jammed

Clearing

Failure to supply the fuel.

Fasteners have become loose

Reinforcing

Содержание KK-TH-525













































Результаты поиска

Содержание KK-TH-525

Отзывы:

Похожие инструкции для KK-TH-525

Бренды по названию

Популярные бренды

KISANKRAFT KK-TH-525, Руководство по эксплуатации

Результаты поиска

Содержание KK-TH-525

Отзывы:

Похожие инструкции для KK-TH-525

Бренды по названию

Популярные бренды