KISANKRAFT KK-PH2-215 Скачать руководство пользователя страница 19

Страница: 19 / 56

Pole Pruner/ Palm Harvester

KK-PP2-8627/ KK-PH2-215



: www.kisankraft.com



: [email protected]



: +91.80.22178200

Page 19 of 56

Filling up with chain oil



Filling up with chain oil



Take care not to spill chain oil while refilling and do not overfill the tank.

Closing the filler cap

To close the oil tank, place the filler cap in position with the grip upright, making sure the

recesses are in alignment.



Turn the filler cap clockwise as far as stop.



Fold the grip down so that it is flush with the top of the cap.

If the oil level in the tank does not go down, the reason may be a fault in the oil supply

system: Check chain lubrication, clean the oilways, contact your dealer for assistance if

necessary We recommend you have servicing and repair work carried out exclusively by

our servicing centers.

Checking Chain Lubrication

The saw chain must always throw off a small

amount of oil.

Never operate your saw without chain

lubrication. If the chain runs dry, the whole cutting

attachment will be irretrievably damaged within a

very short time. Always check chain lubrication

and the oil level in the tank before starting work.

Every new chain has to be broken in for about 2

to 3 minutes. After breaking in the chain, check

chain tension and adjust if necessary

–

see

"Checking Chain Tension".

Preparing for Operations

Adjusting the Telescoping Shaft

Always shut off the engine and fit the chain guard.



Loosen the screw.



Adjust shaft to the required length.



Tighten down the screw firmly.

Fitting the Harness



The type and style of the harness depend on

the market.



Put on the shoulder strap (1).



Adjust the length of the strap.



With the power tool attached, the carabiner

(2) must be at about the same height as your

right hip.

Содержание KK-PH2-215

























































Результаты поиска

Содержание KK-PH2-215

Отзывы:

Похожие инструкции для KK-PH2-215

Бренды по названию

Популярные бренды

KISANKRAFT KK-PH2-215, Руководство по эксплуатации

Результаты поиска

Содержание KK-PH2-215

Отзывы:

Похожие инструкции для KK-PH2-215

Бренды по названию

Популярные бренды