KISANKRAFT KK-PH2-215 Скачать руководство пользователя страница 18

Страница: 18 / 56

Pole Pruner/ Palm Harvester

KK-PP2-8627/ KK-PH2-215



: www.kisankraft.com



: [email protected]



: +91.80.22178200

Page 18 of 56

Fuel mixture at the rate other than 40:1 may cause damage to the engine, Ensure mixture

ratio is correct.

Fuel

The engine uses two-stroke fuel, a mixture of gasoline and 2-stroke lubricant 40:1.

IMPORTANT

Two-stroke fuel may separate. Shake fuel container thoroughly before each use. Stored

fuel ages. Do not mix more fuel than you expect to use within a month.

Fuel and oil mixture

Inspect fuel tank making sure that it is clean and fill with fresh fuel. Use a mixture of 40:1.

Gasoline

Use branded 90 octane or higher no lead gasoline known to be of good quality.

Storing fuel

Store fuel only in a clean, safe, approved container. Check and follow local ordinances on

type and location of storage container.

CAUTION:

The engine exhaust from this product contains chemicals known to cause cancer, birth

defects, or other reproductive harm.

Chain Lubricant

For automatic and reliable lubrication of the chain and guide bar

–

use only an

environmentally compatible quality chain and bar lubricant.

Biological chain oil must be resistant to aging, since it will otherwise quickly turn to

resin. This results in hard deposits that are difficult to remove, especially in the area of the

chain drive and chain.

It may even cause the oil pump to seize.

The service life of the chain and guide bar depends on the quality of the lubricant. It is

therefore essential to use only a specially formulated chain lubricant.

Do not use waste oil. Renewed contact with waste oil can cause skin cancer.

Moreover, waste oil is environmentally harmful.

Waste oil does not have the necessary lubricating properties and is unsuitable for

chain lubrication.

A full chain oil tank is sufficient for only half a tankful of fuel. Check the oil level

regularly during cutting work. Never allow the oil tank to run dry.

Preparations



Thoroughly clean the oil filler cap and the area around it to ensure that no dirt

falls into the tank.



Position the machine so that the filler cap is facing up.

Opening the filler cap

The bayonet-type oil tank filler cap with hinged grip can be opened and closed without

tools.



To open the tank, swing the grip to the vertical position.



Turn the filler cap counterclockwise as far as stop and remove.

Содержание KK-PH2-215

























































Результаты поиска

Содержание KK-PH2-215

Отзывы:

Похожие инструкции для KK-PH2-215

Бренды по названию

Популярные бренды

KISANKRAFT KK-PH2-215, Руководство по эксплуатации

Результаты поиска

Содержание KK-PH2-215

Отзывы:

Похожие инструкции для KK-PH2-215

Бренды по названию

Популярные бренды