background image

Please keep the battery in the clean, dry and ventilated room with     

the temperature of -5

35

 and the relative humidity not more than 

75%, avoid to contacting with any corrosive substance and keep 

away from fire and heat.

If the extended storage is needed, please keep the battery in the 

clean,dry environment without any corrosive substance in the 

temperature of -5

25

. If the time is over three months, the 

battery should have a charging. If keep the battery in the unventilated 

environment with a temperature of over 40

, the battery may leak, 

self-ignite or be damaged by reason of quickening the self discharge. 

The battery kept under the temperature of 40

 should be charged 

once a month and the charging status should be 50% of the battery 

capacity.

The battery life will be shortened if using under the maximum condi- 

tions, such as limiting temperature, deep charging and discharging 

circulation and overcharging / over discharging.

In the extended storage, the battery may be write-off or the capacity 

may reduce seriously without any charging and discharging maint-

enance.

3. Safety

To avoid the leaking, heating, firing or exploding of the battery, please 

comply with the following protective measures.

Do not place the battery in the water; do not keep the battery in the 

damp, unventilated environment with a high temperature for a long 

time.

Do not burn or heat the battery; do not use, place or charge the 

battery near  fire or heat  (over 70

).

Do not reverse the power polarities; do not short-circuit the battery.

Do not connect the battery with battery socket or car battery directly.

Battery and Safety

1. Warranty Exclusions

The company will not be responsible for any failure or safety accident 

generating by using the battery without following the 

Battery and 

Safety Directions

.

The company will not be responsible for any failure generating by 

mismatching circuit which is caused by using no autonomous produc-

ing products, like battery pack, charger and transceiver.

The battery is guaranteed for service for 6 months after leaving the 

factory. In this period, if there is any abnormal condition from the 

battery, you are allowed to change a new one for free, but that is 

based on using the battery in conformity with the directions.

2. Conditions and Environment

Using the special charger appointed by the company.

If the battery charging is full, do not charge it repeatedly in a short   

   time, or that will shorten battery's life or bring safety trouble to you.  

    Please stop charging, if the battery is charged overtime, but not full.

Do not place, charge or use the battery under strong sunlight for a 

long time, or the battery may become heat, fire or fail to use.

The battery has a protecting system for the circuit, it is prohibited to 

    use the battery in  the areas of heavy static (more than 100V) or high 

   magnetic field, or the protecting system will be damaged and bring 

    safety trouble.

The charging temperature is from -10  to 40

, please charge within 

 this range, or the charger may start automatic protection to stop 

 charging or the battery may be damaged.

If an abnormal odor, leak or any other abnormal situation is detected 

   coming from the battery, please do not use it, but return it to the

   dealer.

Содержание PT 3800(1)
















Отзывы: