Kioti CS2610 Скачать руководство пользователя страница 66

Страница: 66 / 170

Cs2610

(1) pTO shift Lever

This lever is to shift the pTO speed

as follows:



rear position (A): Connecting only

to rear pTO



Middle position (b): Connecting

rear and middle pTO



Front position (C): Connecting only

to middle pTO

PTO SHIFT lEvER

M46O434A

(1) Cutting height Adjustment Lever

CuTTING HEIGHT ADJuSTMENT lEvER

M46O452A

Cutting height is controlled by the

height adjustment control lever. The

cutting height can be set to seven dif-

ferent heights.



Deck must be in the "full up"

position before cutting height

can be changed. Do Not at-

tempt to change cutting height

with deck in any other position

than "full up".



when gauge wheels are prop-

erly adjusted, gauge wheels

will not contact the ground!

Gauge wheels are not meant

to continuously contact the

ground, the wheels act as anti

scalp rollers on the four cor-

ners of the deck.

IMPORTANT

M46-EU,AU-04.indd 22

2012-01-19 오후 1:48:47

Содержание CS2610











































































































































































Результаты поиска

Содержание CS2610

Отзывы:

Похожие инструкции для CS2610

Бренды по названию

Популярные бренды

Kioti CS2610, Руководство пользователя

Результаты поиска

Содержание CS2610

Отзывы:

Похожие инструкции для CS2610

Бренды по названию

Популярные бренды