Kioti CS2610 Скачать руководство пользователя страница 31

Страница: 31 / 170

safetY precautions

(11) part no. : t2555-52351

D A N G E R

Improper operating of tractor can rollover

or upset

DO NOT operate vehicle without raised

ROPS and locking pins in position.

DO NOT attach ropes or chains to ROPS

for pulling.

Lower the ROPS for low clearance ONLY.

- NO protection is provided in lowered position.

RAISE ROPS and insert locking pin immediately

after low clearance use, or for transport

ALWAYS wear seat belt with ROPS in

raised position.

Failure to comply will result

death or serious injury

- Seat belt is not recommended with ROPS lowered.

- DO NOT fold ROPS with a conopy

attached

T2555-52351

(12) part no. : t2555-52262

Pull only from approved drawbar

or lower links of 3-point linkage

at horizontal position or below.

Rotating driveline contact may

cause serious injury or death.

Keep all driveline, tractor and

equipment shield in place

during operation.

T2555-52262

M46-EU,AU-01.indd 21

2012-03-09 오전 11:16:13

Содержание CS2610











































































































































































Результаты поиска

Содержание CS2610

Отзывы:

Kioti CS2610, Руководство пользователя, Страница: 31 / 170

Результаты поиска

Содержание CS2610

Отзывы: