Kioti CS2610 Скачать руководство пользователя страница 56

Страница: 56 / 170

Cs2610

ENGINE COOlANT TEMPERATuRE GAuGE

This gauge indicates the coolant

temperature after the key switch is

turned to the “ON” position.
•

: Coolant is cold.

•

: Coolant is hot.

The range marked in “2” in the figure

indicates the normal engine tempera-

ture. (Normal driving range)

(1) Coolant Temperature Gauge

(2) Normal driving range

“C” : Cold

“h” : hot



Make sure to control the work

load so that the needle is not

in the red zone.



If the needle stays in the red

zone with buzzer, do not stop

the engine immediately. In-

stead, reduce the work load to

cool down the engine before

stopping the engine.



Make sure to keep the front

grill clean so that air is sucked

through it freely for fast cooling.

CAuTION

M46O413A

This lamp comes on when the en-

gine oil pressure or oil level is low.
This lamp is turned On when the start-

ing switch is turned On before starting

the engine but turned Off after starting

the engine. If this lamp comes with

buzzer on while driving, stop the engine

immediately and check the engine oil

level.
If this lamp comes on even with the

specified engine oil level, have the

tractor checked by your local

KIOTI

dealer or workshop immediately.

ENGINE OIl PRESSuRE

wARNING lAMP

M46O417A

M46-EU,AU-04.indd 12

2012-01-19 오후 1:48:29

Содержание CS2610











































































































































































Результаты поиска

Содержание CS2610

Отзывы:

Похожие инструкции для CS2610

Бренды по названию

Популярные бренды

Kioti CS2610, Руководство пользователя

Результаты поиска

Содержание CS2610

Отзывы:

Похожие инструкции для CS2610

Бренды по названию

Популярные бренды