Kioti CS2610 Скачать руководство пользователя страница 130

Страница: 130 / 170

cs2610

(1) radiator screen

(2) Bolt

(a) Detach

ClEANING GRIll, RADIATOR sCREEN (G)

To avoid accidents:



Be sure to stop the engine be

fore removing the screen.

CAUTION



Bonnet Grill and screen must

be clean from debris to pre

vent engine from overheating

and to allow good air intake

for the air cleaner.

IMPORTANT

1. check front grill and side screens

to be sure they are clean of debris.

2. unscrew the bolt, lift out the radia-

tor screen and remove all the for-

eign material.

ChECkING BRAkE PEDAls (h)

1. the brake pedals should be in-

spected for free travel, and smooth

operation.

2. you should adjust these pedals

if an incorrect measurement is

found. (see maintenance code "o"

in this chapter)



when depressing the brake ped-

als separated, both brake pedal

should moved down to the same

depth.

NOTE

M46O710A

ChECkING hEAD lIGhT, hAz-

ARD lIGhT ETC. (J)

1. inspect the lights for broken bulbs

and lenses.

2. replace if broken.

ChECkING GAUGEs, METER

AND EAsy ChECk lAMPs (I)

1. inspect the instrument panel for

broken gauge(s), meter(s) and

easy check lamps.

2. replace if broken.

ChECkING sEAT BElT AND

ROPs (k)

1. always check condition of seat

belt and

ROPs

attaching hardware

before operating tractor.

2. replace if damaged.

M46-EU,AU-07.indd 12

2012-01-18 오후 6:39:40

Содержание CS2610











































































































































































Результаты поиска

Содержание CS2610

Отзывы:

Kioti CS2610, Руководство пользователя, Страница: 130 / 170

Результаты поиска

Содержание CS2610

Отзывы: