Kioti CS2610 Скачать руководство пользователя страница 162

Страница: 162 / 170

CS2610

TracTor TroublEshooTing

causE

counTErmEasurEs

1. When tractor does not move

while engine is running



Shift lever is in neutral position



Check the shift levers.



Parking brake is applied



Release the parking brake.

3. Brake is not operating prop

erly



Brake does not operate or

only one brake pedal oper

ates



The brake pedal play is excessive. Adjust the play.



The brake lining is worn or stuck. Have it replaced in a workshop.



Brake pedal does not return

properly



The brake return spring is damaged. Replace it.



Grease is insufficient on each mating surface.

Remove rust and apply grease.

4. Steering wheel is not oper

ating properly



Steering wheel is heavy or

vibrate



The toe-in is incorrect. Adjust it again.



The tire inflation pressure is different. Inflate the left and

right tires into the specified pressure.



Each connection is loose.

Re-tighten each connection and replace the part.



Steering wheel play is exces

sive



The steering wheel shaft is worn. Have it repaired in a

workshop.



Metal parts are worn. Have them repaired in a workshop.



Each connection has play. Tighten the connection again.

M46-EU,AU-09.indd 4

2012-01-18 오후 6:40:32

Содержание CS2610











































































































































































Результаты поиска

Содержание CS2610

Отзывы:

Kioti CS2610, Руководство пользователя, Страница: 162 / 170

Результаты поиска

Содержание CS2610

Отзывы: