Kioti CS2610 Скачать руководство пользователя страница 65

Страница: 65 / 170

desCrIpTION OF OperATING sysTeM



using the accelerator lever

during driving can lead to an

accident as it becomes hard to

decelerate the tractor rapidly.

CAuTION

DIFFERENTIAl lOCK PEDAl

(1) Lock pedal

(A) release to “disengage”

(b) depress to “engage”

The differential lock is to secure the

differential system and keep the

wheel rotation on both sides the

same in order to enhance the trac-

tion of the rear axle.
depressing the pedal engages the

differential lock while releasing the

pedal disengages the differential lock.



The differential lock should be

engaged only while the driving

clutch is engaged. If the differ-

ential lock pedal does not move

when depressing it, try to de-

press it again after releasing it.



when engaging the differential

lock, reduce the engine speed.

After engaging it, accelerate

the tractor.



Make sure to set the steering

wheel in the straight ahead po-

sition while the differential lock

is in use. Otherwise, the differ-

ential system can be damaged.

CAuTION

M46O433A

Use this system under the following

conditions:
1. when any wheel slips and the

tractor does not move in the field.

2. when it is hard to escape a soft or

muddy field.

M46-EU,AU-04.indd 21

2012-01-19 오후 1:48:45

Содержание CS2610











































































































































































Результаты поиска

Содержание CS2610

Отзывы:

Похожие инструкции для CS2610

Бренды по названию

Популярные бренды

Kioti CS2610, Руководство пользователя

Результаты поиска

Содержание CS2610

Отзывы:

Похожие инструкции для CS2610

Бренды по названию

Популярные бренды