Kingfisher KI 7010B Series Скачать руководство пользователя страница 33

Страница: 33 / 46

KI 7010B UM-11

DISCLAIMER AND WARRANTY

Information in this manual is given in good faith for the benefit of the
user. It cannot be used as the basis for claims against Kingfisher

International or its representatives, if accidental damage or
inconvenience results from use or attempted repair of the equipment.

Kingfisher International products are guaranteed against defective
components and workmanship for a period of 3 years from the date of

delivery, unless specifically stated in the original purchase contract or
agreement. This warranty excludes optical connectors or incorrect

use. Opening the instrument will invalidate the warranty. Liability is
limited solely to repair of the equipment.

KINGFISHER INTERNATIONAL PTY LTD

720 Springvale Road, Mulgrave, Victoria 3170 Australia

Phone:

(61) 3-8544-1700

Fax:

(61) 3-8544-1793

E-mail:

[email protected]

Website:

http://www.kingfisherfiber.com

Technical data is subject to change without notice as part of our
program of continuous improvement. Therefore please verify critical

parameters before ordering. Australian and international patents
granted.

Содержание KI 7010B Series















































Результаты поиска

Содержание KI 7010B Series

Отзывы:

Похожие инструкции для KI 7010B Series

Бренды по названию

Популярные бренды

Kingfisher KI 7010B Series, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание KI 7010B Series

Отзывы:

Похожие инструкции для KI 7010B Series

Бренды по названию

Популярные бренды