Kingfisher 2525 Скачать руководство пользователя страница 60

Страница: 60 / 69

KINGFISHER

O W N E R ’ S M A N U A L

w w w . k i n g f i s h e r b o a t s . c o m

Wash Down System

To operate the wash down pump:



Ensure that the ball valve on the wash down water pick up is open. This is clearly

marked and located behind the fuel tank, below the bilge doors.

IMPORTANT:

Whenever the wash down system is not being used, the water pick up

ball valve should be in the off position.



Ensure that battery power is turned on.



Remove the cap from the wash down hose fitting located above the lower tray in the

rear starboard gunnel.

Wash down hose fitting.

Wash down switch.



Attach the hose to the wash down fitting and attach the hose nozzle to the other end

of the hose.



Turn on the wash down pump by operating the switch located underneath the

starboard side rear gunnel.



Hold the hose nozzle open and wait a few seconds for the wash down pump to prime

and supply water.

If the wash down pump fails to work correctly:



Confirm that the battery switch is turned on.



Confirm that the battery system is fully charged and functioning and that all wires

leading to the batteries are secured firmly to the battery posts.



Check that the main 30 amp fuse and the fuse under the dash have not blown.



Once the above has been checked, if the wash down pump is still not working, close

the ball valve and consult an authorized Kingfisher dealer.

Содержание 2525






































































Результаты поиска

Содержание 2525

Отзывы:

Похожие инструкции для 2525

Бренды по названию

Популярные бренды

Kingfisher 2525, Инструкция по эксплуатации

Результаты поиска

Содержание 2525

Отзывы:

Похожие инструкции для 2525

Бренды по названию

Популярные бренды