background image

www.kimray.com

GEN II REPAIR MANUAL
INDEX

Introduction  ....................................................................................................  1

Elastomer Materials .......................................................................................  2

Terminal Arm Disassembly  ...........................................................................  3

Terminal Arm Assembly  ................................................................................  7

Pilot Disassembly  ..........................................................................................  9

Pilot Assembly  .............................................................................................  13

Pilot Installation  ...........................................................................................  15

Settings  .......................................................................................................  17

NOTE:   We reserve the right to modify or change, without prior 

notice, any statement or information contained herein.  If exact 

dimensions or specifications are required by the customer

certified prints will be furnished for a minimum charge upon 

request to KIMRAY, Inc.

® Copyright 2006, KIMRAY, Inc.

Содержание GEN II























Отзывы: