KI ROGUE 2 Скачать руководство пользователя | Manualshive

Страница: 47 / 58

background image

46

Reversing Wheel Lock

5. Reinstall the wheel lock assembly onto the wheel lock bar. For a low profile scissor lock, use a 5mm

Allen wrench to install the two bolts. For the short throw and push to lock flush mount wheel locks,
install hardware using a 4mm Allen wrench and a 10mm wrench. For the push and pull to lock, slide the
assembly back onto the arbors. To install the spring on a push to lock, pull the curved spring arm over
the arbor shoulder. To install the spring on a pull to lock, pull the spring arm end into the wheel lock bar
hole (thin screwdriver will help with this). Place and tighten the top lock nuts to secure. See image
below.

NOTE: Always tighten wheel lock hardware by alternating between the two bolts while tightening a
little at a time. This prevents overclamping on one set of hardware which can lead to binding of the
fasteners and increased difficulty in removal.

6. Test the wheel locks. Ensure wheel lock arms embed in tires at least 1/8 inch when locked. If they do

not embed at least 1/8 inch, readjust wheel lock and test again.

Low Profile
Scissor Lock

Short Thro
Scissor Lock

Push to Lock Flush Mount
Wheel Lock

Push and Pull to Lock
Wheel Locks

«
...
45
46
47
48
49
...
»

Содержание ROGUE 2



























































Отзывы:

Нет отзывов

Похожие инструкции для ROGUE 2

Бренд: R82 Страницы: 3

Бренд: R82 Страницы: 92

Бренд: R82 Страницы: 10

Бренд: R82 Страницы: 17

Бренд: R82 Страницы: 22

Бренд: Felco Страницы: 20

Бренд: Quickie Страницы: 80

Milo OP-PECLB2-MILO-E

Бренд: RST Страницы: 15

Бренд: Costway Страницы: 2

Бренд: Faaborg Rehab Technic Страницы: 9

Бренд: HD Rehab Страницы: 2

Бренд: R82 Страницы: 23

Бренд: Permobil Страницы: 100

Бренд: EZee Life Страницы: 6

Бренд: Walkin’ Pets Страницы: 24

Бренд: Safer Locks Страницы: 2

Бренд: Handicare Страницы: 100

Бренд: Etac Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды