KI ROGUE 2 Скачать руководство пользователя

Страница: 53 / 58

One Arm Drive (OAD)

4. Install the camber mount clamp on the opposite side the same way as steps 2 and 3. Before fully

tightening, install the OAD drive shaft (A) into the two axle mounts.

NOTE: See tables at the end of these instructions for the drive shaft lengths used in different

configurations.
NOTE: Some configurations require one wheel to be installed, then the drive shaft, then the opposite
wheel. These configurations are called out in the Shaft Reference at the end of these instructions.

5. Install the OAD wheels on both sides of chair. Install the OAD wheel with the handrim (A) on the desired

drive side. The OAD wheel with no handrim (B) is the following side and is installed opposite the drive
wheel.

Tires are not shown installed on rims in image
to show the OAD wheel assembly more clearly.

Содержание ROGUE 2



























































Результаты поиска

Содержание ROGUE 2

Отзывы:

Похожие инструкции для ROGUE 2

Бренды по названию

Популярные бренды

KI ROGUE 2, Техническое руководство

Результаты поиска

Содержание ROGUE 2

Отзывы:

Похожие инструкции для ROGUE 2

Бренды по названию

Популярные бренды