KI ROGUE 2 Скачать руководство пользователя

Страница: 52 / 58

One Arm Drive (OAD)

Installation

1. Remove wheels, camber tube and index tower assembly by removing two bolts (A) at the top of the

index towers on each side using a 4mm Allen wrench.

2. Install the camber towers (A) using two bolts and two nuts per side with a 3mm Allen wrench and an

8mm wrench. The location of these camber towers along the seat frame determines COG.

3. Install the camber tube mount clamps (F) onto the camber towers (A) using three bolts (D & B) and

three nuts (E) using a 4mm Allen wrench and an 8mm wrench. The holes used to install the camber
mount clamp onto the camber tower determines seat heat. Use the holes that provide the desired seat
height for the user.

4. The axle mount (C) must be mounted reverse of how it is shown in the image below when using 2

degrees or greater camber. Remove the bolt (B) and nut (E) using a 4mm Allen wrench and an 8mm
wrench, reverse the axle mount and reinstall hardware.

Right Chair Frame View

Содержание ROGUE 2



























































Результаты поиска

Содержание ROGUE 2

Отзывы:

Похожие инструкции для ROGUE 2

Бренды по названию

Популярные бренды

KI ROGUE 2, Техническое руководство

Результаты поиска

Содержание ROGUE 2

Отзывы:

Похожие инструкции для ROGUE 2

Бренды по названию

Популярные бренды