Keysight N5227B Скачать руководство пользователя страница 329

Страница: 329 / 415

Keysight N5227B Service Guide 7-11

Repair and Replacement Procedures
Removing and Replacing the A1–A3 and Other Front Panel Subassemblies

Removing the Speaker Assembly

Disconnect the speaker cable from the interface board.

Remove the speaker assembly and speaker foam.

Removing the A3 Display Assembly and the Touchscreen

Disconnect the following cables from the A1 front panel interface board:

tape (item [14]) from connector and the LCD display to interface board

cable (item [18]), LED driver board (backlight converter board) to interface

board (item [11]), touch screen controller board to interface board cable

(item [13]), power switch board to interface board cable (item [12]), and

the speaker assembly cable.

Remove eleven outer screws (item

⑤

) from the A3 display assembly’s

mounting plate and remove the A3 display assembly from the front panel

assembly.

Raise the retaining clamps on the LCD display flat flex cable’s two

connectors (item [15]).

Disconnect the flat flex cable from the touchscreen (item [15]).

The LED driver board cable (item 22) can be removed from the connection

on the LCD Display.

The LCD display cable (item [18]) can be removed by removing the three

screws (item [17]) that attach it to the LCD display mounting bracket.

Remove the 3 screws on the slotted hole side of the mounting plate (item

[20]).

Remove the 3 screws on the round hole side of the mounting plate (item

[20]).

With a T-6 TORX (set to 3-in-lb), remove the 2 screws (item [23]) on the

side bracket that has the LCD cable (item [18]) attached to the LCD

display.

10.

With a T-6 TORX (set to 3-in-lb), remove the 2 screws (item 23) on the 2nd

side bracket (item [21]).

When handling the speaker avoid touching the top of the speaker. Hold

only the sides of the speaker when re-attaching the new foam.
Avoid covering the Mounting Plate screw.

During re-assembly of the side brackets to the LCD display, it is very

important to avoid over-tightening.

During re-assembly of the side brackets to the LCD display, it is very

important to avoid over-tightening.

Содержание N5227B
































































































































































































































































































































































































































Результаты поиска

Содержание N5227B

Отзывы:

Похожие инструкции для N5227B

Бренды по названию

Популярные бренды

Keysight N5227B, Руководство по обслуживанию

Результаты поиска

Содержание N5227B

Отзывы:

Похожие инструкции для N5227B

Бренды по названию

Популярные бренды