Keysight Technologies U3050BH11 Скачать руководство пользователя страница 42

Страница: 42 / 48

Safety and Regulatory Information

U3050BH11

General Safety Considerations

Cautions applicable to this instrument.

The Mains wiring and connectors shall be compatible with the connector

used in the premise electrical system. Failure, to ensure adequate earth

grounding by not using the correct components may cause product

damage, and serious injury.

Always use the three prong AC power cord supplied with this product.

Failure to ensure adequate earth grounding by not using this cord may

cause product damage and the risk of electrical shock.

This product is designed for use in Installation Category II and

Pollution Degree 2.

Verify that the premise electrical voltage supply is within the range

specified on the instrument.

Ventilation Requirements: When installing the instrument in a cabinet, the

convection into and out of the instrument must not be restricted. The

ambient temperature (outside the cabinet) must be less than the maximum

operating temperature of the instrument by 4 °C for every 100 watts

dissipated in the cabinet. If the total power dissipated in the cabinet is

greater than 800 watts, forced convection must be used.

Keysight U3050BH11 User's and Service Guide

Содержание U3050BH11

















































Результаты поиска

Содержание U3050BH11

Отзывы:

Похожие инструкции для U3050BH11

Бренды по названию

Популярные бренды

Keysight Technologies U3050BH11, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U3050BH11

Отзывы:

Похожие инструкции для U3050BH11

Бренды по названию

Популярные бренды