Keysight Technologies U3050BH11 Скачать руководство пользователя страница 43

Страница: 43 / 48

U3050BH11

Safety and Regulatory Information

Warnings applicable to this instrument

Danger of explosion if battery is incorrectly replaced. Replace only with

the same or equivalent type recommended. Discard used batteries

according to manufacturer’s instructions.

This is a Safety Class I product (provided with a protective earthing ground

incorporated in the power cord). The mains plug shall be inserted only into

a socket outlet provided with a protective earth contact. Any interruption of

the protective conductor, inside or outside the product is likely to make the

product dangerous. Intentional interruption is prohibited.

These servicing instructions are for use by qualified personnel only. To

avoid electrical shock, do not perform any servicing unless you are

qualified to do so.

The opening of covers or removal of parts is likely to expose the user to

dangerous voltages. Disconnect the instrument from all voltage sources

before opening.

This product is designed for use in Installation Category II and Pollution
Degree 2.

No operator serviceable parts inside. Refer servicing to qualified

personnel.

If this product is not used as specified, the protection provided by the
equipment could be impaired. This product must be used in a normal
condition (in which all means for protection are intact) only.

The power cord is connected to internal capacitors that remain live for

five seconds after disconnecting the plug from its power supply.

Keysight U3050BH11 User's and Service Guide

Содержание U3050BH11

















































Результаты поиска

Содержание U3050BH11

Отзывы:

Похожие инструкции для U3050BH11

Бренды по названию

Популярные бренды

Keysight Technologies U3050BH11, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U3050BH11

Отзывы:

Похожие инструкции для U3050BH11

Бренды по названию

Популярные бренды