Keysight Technologies U3050BH11 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 48

background image

U3050BH11

System Setup with N5245A

4. Remove the two upper feet from the U3050BH11 and install the two locking feet

N5242-20206 (right foot) and the N5242-20207 (left foot) using two screws (0515-2317) as

shown in

5. Place the PNA-X on top of the U3050BH11. Ensure that the front frame of the PNA-X is

positioned slightly forward of the locks that are attached to the Test Set. Slide the PNA-X

back so the locks engage the front frame of the analyzer as shown in

Figure

7

Rear Panel N5245A with U3050BH11

Figure 8

Locking the Analyzers

N5242-20206

N5242-20207

Slide the network analyzer
back to engage the Lock Link
in the back of the network
analyzer's front frame

Screw

Network Analyzer
Front Frame

Test Set

Front Frame

Lock Link

10

Keysight U3050BH11 User's and Service Guide

«
...
12
13
14
15
16
...
»

Содержание U3050BH11

















































Отзывы:

Нет отзывов

Похожие инструкции для U3050BH11

Бренд: Febco Страницы: 12

Бренд: Yetter Страницы: 16

Бренд: Bard Страницы: 144

Бренд: GALBIATI Страницы: 8

Бренд: Vahva Jussi Страницы: 9

Бренд: h/p/cosmos Страницы: 81

Бренд: jablotron Страницы: 2

Бренд: jablotron Страницы: 2

Бренд: York Страницы: 26

Бренд: S.R.Smith Страницы: 8

Бренд: S.R.Smith Страницы: 23

NavBoard ZipFlip

Бренд: S&S Precision Страницы: 6

Бренд: Tascam Страницы: 78

MINISTUDIO CREATOR US-42

Бренд: Tascam Страницы: 11

Бренд: Vatech Страницы: 137

Бренд: Vatech Страницы: 68

Бренд: Varytec Страницы: 52

Бренд: Yamaha Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды