Keysight Technologies 8480 Series Скачать руководство пользователя страница 15

Страница: 15 / 99

Introduction

Keysight 8480 Series Operating and Service Manual

power meter. Suitable and compatible power meters are the EPM series power

meters (E4418B and E4419B), the EPM-P series power meters (E4416A and

E4417A) and the E1416A VXI power meter. Discontinued and obsolete power

meters that are compatible with the 8480 series sensors include the E4418A,

E4419A, 435B, 436A, 437B, 438A and 70100A MMS power meter.
The 8480 series power sensors place a 50 ohm load on the RF or microwave

source, except the 8483A which has a 75 ohm load. The power meter indicates

the power dissipated in this load in mW or dBm.
The coaxial power sensors in the 8480 series measure power levels from -70 dBm

to +44 dBm (100 pW to 25 W), at frequencies from 100 kHz to 50 GHz. To cover

this wide dynamic power range, both thermocouple and diode power sensing

elements are used. Both types of power sensing elements have a maximum 50 dB

dynamic range. Thermocouple sensors have a square-law region from -30 dBm to

+20 dBm, and with an attenuator can operate up to +44 dBm. There are three

model types of thermocouple sensors in the 8480 series, covering the complete

-30 dBm to +44 dBm range.
– The A-models cover -30 dBm to +20 dBm.
– The H-models cover from -10 dBm to +35 dBm.
– The B-models cover from 0 dBm to +44 dBm.
Diode detectors (D-models) have the best sensitivity, having an operating range

from -70 dBm to -20 dBm.
Calibration factor (CAL FACTOR) data is provided on a label attached to the power

sensor's cover. Maximum uncertainties of the CAL FACTOR data are listed in the

Specifications section in page 23. This calibration factor is used to adjust the

power meter to suit the particular power sensor and frequency being measured.

NOTE

For the B-models in the 8480 series, calibration factor data is valid only when

the sensor is used with the supplied attenuator.

Содержание 8480 Series




































































































Результаты поиска

Содержание 8480 Series

Отзывы:

Похожие инструкции для 8480 Series

Бренды по названию

Популярные бренды

Keysight Technologies 8480 Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 8480 Series

Отзывы:

Похожие инструкции для 8480 Series

Бренды по названию

Популярные бренды