Keysight Technologies 8480 Series Скачать руководство пользователя страница 57

Страница: 57 / 99

Service

Keysight 8480 Series Operating and Service Manual

Diode sensors

The A1 Bulkhead Assembly presents a 50 Ohm load to the RF source.
A diode assembly in the bulkhead rectifies the applied RF to produce a dc voltage

that varies with the square of the RF power across the 50 Ohm load. Thus the

voltage varies with the RF power dissipated in the load.
This low level DC voltage is passed on gold wires through ferrite beads A2E1 and

A2E2. The ferrite beads increase the self-inductance of the gold wires causing this

portion of the wires to provide the properties of an RF choke. The result is to

minimize RF feedthrough to the A2 Power Sensor Board Assembly.
The dc output from the bulkhead assembly is applied to the two field effect

transistors (FETs) in A2U1. These transistors function as a sampling gate or

chopper. The sampling rate is controlled by a 220 Hz square wave supplied by the

power meter. The amplitude of the sampling gate output (at pin 3 of A2U1) is a

220 Hz square wave proportional to the power input. The sampled 220 Hz ac

output is applied to the input amplifier A2Q1, which is the input stage for an

operational amplifier.
The A2 Power Sensor Board Assembly also contains various components that

comprise a shaping network. This network brings about a linear change in the

amplitude of the square wave output as RF input power changes. A shaping

network is necessary in diode power sensors to compensate for the

characteristics of the thermocouple type shaping in the power meter, and to make

minor diode corrections. In order to bring about a linear change in amplitude, the

components in this network are factory selected to match variations of the diode

assembly in the bulkhead.
The Auto Zero Feedback circuit is coupled to the power sensor from the power

meter. The dc voltage used to set the zero level is applied to the input of FET

A2U1 by using A2R1 and A1TC1 as a voltage divider.
When the Power Sensor is used with a Power Meter, the resistance to ground from

J1-K (Mount Resistor) allows the Power Meter to determine the sensor's dynamic

range.

Содержание 8480 Series




































































































Результаты поиска

Содержание 8480 Series

Отзывы:

Бренды по названию

Популярные бренды

Keysight Technologies 8480 Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 8480 Series

Отзывы:

Бренды по названию

Популярные бренды