Keysight Technologies 8480 Series Скачать руководство пользователя страница 23

Страница: 23 / 99

Introduction

Keysight 8480 Series Operating and Service Manual

8480 Series Power Sensor Specifications

The 8480 series thermocouple and diode power sensors provide accuracy,

stability, and SWR over a wide range of frequencies (100 kHz to 50 GHz) and

power levels (-70 dBm to +44 dBm)

NOTE

These specifications are valid with EPM and EPM-P Series of power meters.

Table 1-3

Typical measurement uncertainties of Calibration Factor (CF)

data printed on the power sensor

Frequency

25°C ± 3°C

8481A

8482A

8483A

8485A

100 kHz to 10 MHz

0.87

1.59

10 MHz to 30 MHz

0.81

0.8

1.39

30 MHz to 500 MHz

0.78

0.8

1.41

1.29

500 MHz to 1.2 GHz

0.78

0.8

1.41

1.26

1.2 GHz to 6 GHz

0.92

0.9

1.46

1.35

6 GHz to 14 GHz

1.16

1.61

14 GHz to 18 GHz

1.59

1.77

18 GHz to 26.5 GHz

2.47

26.5 GHz to 33 GHz

3.35

[a]

[a] These uncertainties only apply to Option 033.

33 GHz to 34 GHz

34 GHz to 35 GHz

35 GHz to 40 GHz

40 GHz to 45 GHz

45 GHz to 50 GHz

Содержание 8480 Series




































































































Результаты поиска

Содержание 8480 Series

Отзывы:

Похожие инструкции для 8480 Series

Бренды по названию

Популярные бренды

Keysight Technologies 8480 Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 8480 Series

Отзывы:

Похожие инструкции для 8480 Series

Бренды по названию

Популярные бренды