Keston Combi 30 Скачать руководство пользователя страница 58

Страница: 58 / 68

Fault Finding

aul

inding

aul

inding

aul

inding

aul

inding

aul

inding

Keston Combi -

Installation and Servicing

76 OVERhEAT LOCKOUT - 1 FILL sysTEM TO 1.0 BAR - 2 BLEED RADIATORs -

3 ChECK RADIATOR VALVEs OpEN - 4 REsET BOILER - 5 CONTACT INsTALLER

Is the Boiler and CH System filled with water and all

isolation and radiator valves open?

YES

Fill and vent the system and open all

isolation valves, then reset boiler

Is the Flow/Return Differential across the Boiler in

excess of 30°C?

Check that the Pump is rotating freely. Is

the Differential now below 20°C?

YES

Replace the Pump,

then reset boiler

OK, now

reset boiler

YES

REsET pROCEDURE

- To reset boiler, turn mode knob to reset

position and immediately turn knob back to required setting.

Check the Return Thermistor (Refer to Frame 49)

Check resistance using a suitable multimeter

connected across the thermistor’s terminal pins

At 25

C expect

9,700 - 10,300

Ohms

At 60

C expect

2,400 - 2,600 Ohms

At 85

C expect

1,000 - 1,100 Ohms

77 IgNITION LOCKOUT / FLUE OVERhEAT - 1 ChECK OThER gAs AppLIANCEs WORK

- 2 REsET BOILER - 3 CONTACT INsTALLER

If the boiler is reset does the boiler ignite

for a short time and then extinguish?

YES

Is the Gas Pressure available at

the Boiler Inlet (>18 mbar)?

Check the detection electrode and

associated harness for: continuity,

visual condition and position (Refer to

Frame 52). Check if the condensate

pipe is blocked. Replace as necessary

Check gas supply and

rectify fault

YES

Is approx 215Vdc supply available

at the Gas Valve? (* See note)

YES

Check spark generator and associated

harness for: continuity and visual

condition. (Refer to Frame 53) Are

these functioning correctly?

Check ignition electrode and associated

harness for: continuity, visual condition

and position. (Refer to Frame 51) Are

these functioning correctly?

Check siphon and condensate drain

pipe work for blockage and rectify if

necessary. Boiler now working OK?

Check wiring connection

from gas valve to PCB for

continuity. If the wiring is

OK then replace the PCB

Replace Spark

Generator and harness

as necessary

Replace Ignition Electrode and

associated harness as necessary

Check if burner is damaged

Unplug gas valve. Is resistance

between outside pins 4K

Ω

(±2)?

YES

Replace Gas Valve

YES

REsET pROCEDURE

- To reset

boiler, turn mode knob to reset

position and immediately turn

knob back to required setting.

Check flue for obstruction

Check wiring to thermostat

Check flue temperature always

remains below 90ºC

YES

Clear obstruction

YES

Ensure wiring correctly

connected

YES

Replace Thermostat

Replace heat exchanger

* note:

due to the wave form of

the rectified voltage, the reading

will vary depending on the type

of meter used to measure the

value. In general terms a reading

greater than 150V indicates that

the correct voltage is supplied to

the gas valve.

Replace burner

207895-2.indd 58

02/01/2013 09:38:50

Содержание Combi 30





































































Результаты поиска

Содержание Combi 30

Отзывы:

Бренды по названию

Популярные бренды

Keston Combi 30, Инструкции по установке и обслуживанию

Результаты поиска

Содержание Combi 30

Отзывы:

Бренды по названию

Популярные бренды