manualshive.com logo in svg

Keston Combi 30, Инструкции по установке и обслуживанию

Поделиться
Скачать
Keston Combi 30 Скачать руководство пользователя страница 29

29

INSTALLATION

Keston Combi - 

Installation and Servicing

 

29  ExTERNAL ELECTRICAL CONTROLs

Wiring External to the Boiler

The fuse rating should be 3A.
Wiring external to the boiler MUST be in accordance with 

the current I.E.E. (BS.7671) Wiring Regulations and any 

local regulations.

Frost protection

If parts of the pipework run outside the house or if the 

boiler will be left off for more than a day or so then a frost 

thermostat should be wired into the system.
This is usually done at the programmer, in which case the 

programmer selector switches are set to OFF and all the 

other controls MUST be left in the running position.
The frost thermostat should be sited in a cold place but 

where it can sense heat from the system.

Note

.

  If the boiler is installed in a garage it may be 

necessary to fit a pipe thermostat, preferably on the return 

pipework.

Earths are not shown for clarity but must never be 

omitted.

OpenTherm programmable Room Temperature Control

Note.

 These terminals MUST ONLY be connected to an 

OpenTherm Controller, (such as the Keston Chronothern Room 

Controller (c.17.4.21.00.0).  Connecting any other device / 

control wiring may destroy the primary PCB.

1.

  Isolate the mains supply to the boiler.

2.

  Remove the front panel.  Refer to Frame 39.

3.

  Swing the control box down into the servicing position.  Refer 

to Frame 45.

4. 

Remove the control box cover.  Refer to Frame 57, no’s 3 

and 4.

5. 

Unclip the 3 way in-line connector containing 2 purple wires 

and 2 red wires.

6. 

Connect this 3 way connector to the 3 way connector 

containing 2 purple wires wired from the 4 way terminal 

block.

7. 

Connect the two wires from the OpenTherm Programmable 

Room Temperature Control to the two LH connections of the 

terminal block as shown.

8. 

Re-assemble in reverse order.

5

6

7

3G9990a

L N

Room Stat

Frost Stat

Mains In

Programmable Room Stat

L N

Room Stat

Frost Stat

Mains In

Use of General Live for Room Stat

Programmable

Room

Stat

Room

Stat

Optional

Frost Stat

Optional

Frost Stat

IN

s

T

ALLA

TION

207895-2.indd   29

02/01/2013   09:38:30

Содержание Combi 30





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды