manualshive.com logo in svg

Keston Combi 30, Инструкции по установке и обслуживанию

Поделиться
Скачать
Keston Combi 30 Скачать руководство пользователя страница 18

18

 

INSTALLATION

Keston Combi - 

Installation and Servicing

13   INsTALLINg ThE BOILER

Installation of the boiler is straightforward but consideration must be given to access to allow flue and air pipes to be pushed 

through walls and ceilings. The order in which the components are installed will depend upon particular site conditions, but in 

general it will be easiest and most accurate to install the boiler and then build up the flue outlet and air inlet pipes to the terminal 

- this is the sequence described.

The wall mounting template is located on the internal protective 

packaging.

Note. 

 

The template shows the positions of the fixing holes and 

the position of the air and flue connections.  Care MUST be 

taken to ensure the correct holes are drilled.

1.

  Tape template into the selected position.  Ensure squareness 

by hanging a plumbline as shown. 

2.

  Mark onto the wall the following:

 a

  The wall mounting plate screw positions (choose one from 

each group).

 

b

  The position of the air and flue when exiting straight out of 

the wall where the boiler is mounted.

Note.

 

Mark the centre of the hole as well as the  

circumference.

3.

  Remove the template from the wall.

14  WALL MOUNTINg TEMpLATE

15  pREpARINg ThE WALL

IMpORTANT.

 

Ensure that, during the cutting operation, masonry falling 

outside of the building does not cause damage or personal 

injury.

1.

  Cut the flue and air holes (preferably with 60mm core bore 

tool) ensuring the holes are square to the wall.

2.

  Drill 2 holes with a 7.5mm / 8mm masonry drill and insert 

the plastic plugs, provided, for the wall mounting plate.

3.

  Locate 2 No.14 x 50mm screws in the wall mounting plate 

(one at each side, in any of the 3 holes provided at each 

side) and screw home.

3G10030

X

Section

through wall

Note. 

Check all of the hole

positions before drilling.

Rear flue only

60mm diameter

holes

IN

s

T

ALLA

TION

207895-2.indd   18

02/01/2013   09:38:20

Содержание Combi 30





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды