Keston Combi 30 Скачать руководство пользователя страница 33

Страница: 33 / 68

INSTALLATION

Keston Combi -

Installation and Servicing

ThE DIspLAy

The user control has one neon and one display to inform the user about the status. The display will show the status of the boiler.

The neon will show the status of the flame. If no flame is detected the neon is off. When the flame is detected the neon will be lit

permanently.
The display scrolls through a maximum of 3 messages under any operational condition as shown below.

Notes:

Boiler frost protection - boiler fires if temperature is below 5º C.

The temperatures shown below are for illustration purposes only. The measured temperatures will be shown on the boiler.

33 INITIAL LIghTINg . . . . CONT’D

NORMAL OPERATION

MESSAGE 1

MESSAGE 2

MESSAGE 3

Mode knob in standby position and no

heat demand

Standby mode

For hot water turn mode

knob clockwise

For central heating turn

mode knob clockwise twice

Mode knob in summer position and no

heat demand

Summer mode

For central heating turn

mode knob clockwise

Mode knob in winter position and no

heat demand

Winter mode

Timer or room stat off

Domestic hot water operation

Hot water

Temperature 64ºC

High efficiency

Central heating operation

Radiator Temp 80ºC

High efficiency

Pre-heat operation

Pre heat

Central heating

Temperature 59ºC

High efficiency

Boiler frost protection

Temperature 5ºC

Pump overrun

Fan post-purge

High efficiency

Note. High efficiency will not be shown for central heating operation if the central heating flow temperature knob is set to greater than 73ºC.

3G971

DIspLAy FUNCTIONs IN NORMAL OpERATION

NORMAL OPERATION

MESSAGE 1

MESSAGE 2

MESSAGE 3

Pre-heat knob moved to off position

Pre heat off

Pre-heat knob moved to on position

Pre heat on

DHW temperature knob moved

64ºC DHW temp

Hot water

temperature 64ºC

CH temperature knob moved

80ºC CH temp

Maximum radiator

temperature 80ºC

May not be achieved for

high flow rates in winter

Mode knob moved to standby position

Central heating off

Hot water off

Mode knob moved to summer position

Summer mode

Standby mode

Central heating off

Hot water on

Mode knob moved to winter position

Winter mode

Central heating on

Mode knob moved to reset position

Reset

Hot water on

3G9712

DIspLAy FUNCTIONs - sETTINgs ChANgED

ALLA

TION

207895-2.indd 33

02/01/2013 09:38:33

Содержание Combi 30





































































Результаты поиска

Содержание Combi 30

Отзывы:

Бренды по названию

Популярные бренды

Keston Combi 30, Инструкции по установке и обслуживанию

Результаты поиска

Содержание Combi 30

Отзывы:

Бренды по названию

Популярные бренды