manualshive.com logo in svg

Keston Combi 30, Инструкции по установке и обслуживанию

Поделиться
Скачать
Keston Combi 30 Скачать руководство пользователя страница 52

52

 

SERVICING

Keston Combi - 

Installation and Servicing

1.

  Refer to Frame 45.

2.

  Drain the boiler. Refer to Frame 60.

3. 

Remove condensate trap/siphon.  Refer to Frame 56.

4. 

Remove the diverter valve actuator.  Refer to Frame 55.

5. 

Remove the 2 allen screws securing the plate heat 

exchanger to the brass housings.

6.

  Manoeuvre the plate heat exchanger out of the top LH or 

centre of the controls area.

66  DhW pLATE hEAT ExChANgER REpLACEMENT

5

67  pUMp hEAD REpLACEMENT

1.

  Refer to Frame 45.

2.

  Drain the boiler. Refer to Frame 60.

3. 

Disconnect the electrical plug from the 

pump.

4.

  Remove the 4 Allen screws retaining the 

pump head.

5.

  Remove the pump head.

6.

  Fit the new pump head.

7.

  Reassemble in reverse order.

8.

  Refill the boiler.  Refer to Frame 22.

9.

  Check operation of the boiler. Refer to 

Frame 36.

3

4

7.

  Fit the new plate heat exchanger, using the new o-rings 

supplied. 

 

Note.

 The mounting pins are offset so the correct position 

can be defined from the location of the holes on the brass 

mounting.

8.

  Reassemble in reverse order.

9. 

Refill the boiler. Refer to Frame 22.

10.

 Check operation of the boiler. Refer to Frame 36.

sER

VICIN

g

207895-2.indd   52

02/01/2013   09:38:47

Содержание Combi 30





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды