Keston Combi 30 Скачать руководство пользователя страница 36

Страница: 36 / 68

INSTALLATION

Keston Combi -

Installation and Servicing

37 hANDINg OVER

Loss of system water pressure

Explain that the dial underneath the boiler indicates the

central heating system pressure and that if the normal COLD

pressure of the system is seen to decrease over a period of

time then a water leak is indicated. Explain the re-pressurising

procedure and if unable to re-pressurise or if the pressure

continues to drop a registered local heating installer should be

consulted.

Explain boiler reset procedure (refer to Frame 35).

10.

After installation and commissioning please complete

the

Commissioning Checklist before

handover to the customer. For IE, its is necessary to complete

a “Declaration of Conformity” to indicate compliance to I.S.

813:2002.

IMpORTANT
11.

A comprehensive service should be carried out ANNUALLY.

Stress the importance of regular servicing by a Gas Safe

Registered Engineer. In IE servicing work must be carried out

by a Registered Gas Installer (RGII).

12.

Inform the householder of the guarantee form and the

requirement to register it to receive the full benefit of the

warranty.

Make the householder aware that the user instructions

are located in the pocket in the drop down door and

explain his/her responsibilities under the relevant national

regulations.

Explain and demonstrate the lighting and shutting down

procedures.

The operation of the boiler and the use and adjustment

of all system controls should be fully explained to

the householder, to ensure the greatest possible fuel

economy consistent with the household requirements of

both heating and hot water consumption.

Advise the User of the precautions necessary to prevent

damage to the system and to the building, in the event of

the system remaining inoperative during frosty conditions.

Explain the function and the use of the boiler heating and

domestic hot water controls.

Explain that due to system variations and seasonal

temperature fluctuations DHW flow rates/temperature

rise will vary, requiring adjustment at the draw off tap. It

is therefore necessary to draw the users attention to the

section in the Users Instructions titled “Control of Water

Temperature” and the following statement:

“Additionally, the temperature can be controlled by

the user via the draw-off tap: the lower the rate the

higher the temperature, and vice versa”

Explain the function of the boiler fault mode.

Emphasise that if a fault is indicated, the boiler should be

turned off and a Gas Safe Registered Engineer consulted.

In IE contact a Registered Gas Installer (RGII).

Explain and demonstrate the function of time and

temperature controls, radiator valves etc., for the

economic use of the system.

If a timer is fitted draw attention to the timer Users

Instructions and hand them to the householder.

After completing the installation and commissioning of the system the installer should hand over to the householder by

the following actions:

ALLA

TION

207895-2.indd 36

02/01/2013 09:38:35

Содержание Combi 30





































































Результаты поиска

Содержание Combi 30

Отзывы:

Бренды по названию

Популярные бренды

Keston Combi 30, Инструкции по установке и обслуживанию

Результаты поиска

Содержание Combi 30

Отзывы:

Бренды по названию

Популярные бренды