Kessel 917824, Инструкции по установке, эксплуатации и обслуживанию

Страница: 40 / 196

3. Installation and Assembly
3.3 Installation dimensions of sensor
40
Freie Auf-
stellung
Artikelnummer NS
Abstand Oberkante
unterer Finger zu
Unterkante Auslauf
(Wasserlinie)
Alarmschichtdicke
in cm Voralarmschichtdicke
in cm bei 80%
max. Schlammschicht-
dicke in cm = 50% des
Schlammfangvolumen
G 93002.01 /.02 /.11 /.12 /.21 /.22 /.31 /.32 2 50 cm 14 11 22
93003.01 /.02 /.11 /.12 /.21 /.22 /.31 /.32 3 50 cm 17 14 29
93004.01 /.02 /.11 /.12 /.21 /.22 /.31 /.32 4 50 cm 17 14 30
93007.01 /.02 /.11 /.12 /.21 /.22 /.31 /.32 7 50 cm 21 17 35
93010.01 /.02 /.11 /.12 /.21 /.22 /.31 /.32 10 50 cm 21 17 38
98201 (Obere beiden Bohrlöcher der Bohrschablone verwenden) 1 58 cm 16 13 46
98202 (Obere beiden Bohrlöcher der Bohrschablone verwenden) 2 58 cm 16 13 54
D 93002.01 D /.02 D /.11 D /.12 D /.21 D /.22 D /.31 D /.32 D 2 50 cm 14 11 22
93003.01 D /.02 D /.11 D /.12 D /.21 D /.22 D /.31 D /.32 D 3 50 cm 17 14 29
93004.01 D /.02 D /.11 D /.12 D /.21 D /.22 D /.31 D /.32 D 4 50 cm 17 14 30
93007.01 D /.02 D /.11 D /.12 D /.21 D /.22 D /.31 D /.32 D 7 50 cm 21 17 35
93010.01 D /.02 D /.11 D /.12 D /.21 D /.22 D /.31 D /.32 D 10 50 cm 21 17 38
98201.00/D1 (Obere beiden Bohrlöcher der Bohrschablone verwenden) 1 58 cm 16 13 46
98202.00/D1 (Obere beiden Bohrlöcher der Bohrschablone verwenden) 2 58 cm 16 13 54
free
standing
Article No.
Distance between the
upper edge of the
lower “finger” and the
lower edge of the out-
let (water line)
Alarm level layer
thickness in cm
Recommended pre-
liminary alarm level in
cm (= 2/3 of the max.
storage volume)
max. sludge layer in cm
( = 50% of sludgetrap
volume)
After installation and commissioning of an EasyClean grease separator with a control unit, the following two values for grease layer
thickness must be changed. Please do the following:
Enter the ‘3.1 Settings’ section on the digital display of the control unit.
- Enter the access code – 1000
- 3.1.1 Alarm layer thickness (change to the appropriate value shown below)
- 3.1.2 Pre-Alarm layer thickness (change to the appropriate value shown below)