Keofitt W9 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 50

Keofitt W9 Скачать руководство пользователя страница 23

KEOFITT W9 USER MANUAL V.4

PAGE 23

5.3 Steam sterilisation

Chemical CIP and chemical disinfection are usually not needed when using steam, as steam does it all.

An exception from this is with sugary substances, which caramelise and with substances containing

protein, which coagulate and burn; see chapter 2.1. In this case flushing with an appropriate fluid must

precede post-sampling steaming.

Steam sterilisation takes place with the valve remaining in its closed position. Perform the following

steps:

1. Remove the plugs from the hose pieces.

2. Connect the steam hose to the valve’s upper hose piece.

3. Connect a hose to the lower hose piece and let it go to drain.

4. Open the steam supply and let it flow through the valve for

sterilisation. Allow 1 minute at 121° C (1 bar(g)).

5. Close the steam supply, but leave the hose in place to prevent

contamination from the ambient during sampling. If removal of steam

hose is required, fit a sterile rubber or stainless steel plug onto the

upper hose piece.

The valve is now ready to take a sample. The sampling must be performed immediately after steaming to

avoid any contamination of the sample.

WARNING

• During sterilisation with steam the valve will become hot and care should thus be taken when

operating the valve

• The valve is designed for use in working conditions of up to 6-12 bar(g) pressure (depending on

«
...
21
22
23
24
25
...
»

Содержание W9



















































Отзывы:

Нет отзывов