manualshive.com logo in svg

Keofitt W9, Руководство пользователя, Страница: 18 / 50

Поделиться
Скачать
Keofitt W9 Скачать руководство пользователя страница 18

KEOFITT W9 USER MANUAL V.4 

PAGE 18

3.  Intermediate rinse 

Rinse with clean water to remove all traces of detergents

4. Disinfection 

Apply an appropriate disinfectant targeting one or more or all microorganisms 

5.  Final rinse 

Rinse with cleaned water to remove all traces of the disinfectant

4.4  Steam sterilisation

Steaming has the advantage that it does flushing, cleaning and sterilisation in one operation. However 

the heat from the steam will cause sugary substances to caramelise and substances containing protein 

to coagulate and burn; see chapter 2.1. In this case flushing with an appropriate fluid must precede post-

sampling steaming.  

If steaming is the preferred procedure, but no steam is installed near the sampling point, an option is 

to use a portable steam generator. Keofitt supplies an adapter for a Kärcher steam generator as well 

as other mobile steam supply systems. The steaming process with a Keofitt sampling valve has been 

validated to obtain sterility after 1 minute of steaming at 121° C (1 bar(g)). Documentation is available at 

the Keofitt Online Service Center on www.keofitt.dk.

4.5 Sampling

Once the cleaning/disinfecting/sterilising is accomplished taking a sample is done by opening the valve 

and closing it again once the require sample volume is obtained.

For detailed operator instructions see chapter 5.4.

Содержание W9



















































Отзывы:

Нет отзывов