Keofitt W9 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 50

Keofitt W9 Скачать руководство пользователя страница 21

KEOFITT W9 USER MANUAL V.4

PAGE 21

5.2 Chemical disinfection

Immediately following the CIP, perform the disinfection, if required. The disinfection takes place with the

valve remaining in its closed position.

There are 2 recommended ways to carry out the disinfection:

A) by letting the disinfectant flow through the valve chamber

B) by filling the valve chamber with the disinfectant (advantage: smaller volume of disinfectant

needed and quicker and more reliable disinfection)

Steps to perform, when adopting A:

1. Connect a hose with an empty bottle to the lower hose piece. This

bottle or similar recipient is to collect the disinfectant (step 3) and the

rinsing water (step 6).

2. Fill a flexible bottle with the defined amount of disinfectant.
3. Connect the flexible bottle via a hose to the upper hose piece and

press the disinfectant slowly through the valve to wet the interior of

the valve.

4. Allow the disinfectant to act for the prescribed time.
5. Disconnect the hose from the upper hose piece and connect a flexible

bottle with cleaned water to the upper hose piece.

6. Rinse through the upper hose piece by squeezing the bottle, thus

pressing the water through the valve chamber.

7. Leave the squeezed bottle connected to the hose piece and clamp

the hose to avoid contamination from air being sucked in through the

valve.

«
...
19
20
21
22
23
...
»

Содержание W9



















































Отзывы:

Нет отзывов