Kenwood TS-990S, Инструкция по эксплуатации

Страница: 263 / 290

USEFUL FUNCTIONS 16
16-31
Index Contents
TS-990S + TH-D72A/E, TM-D710A/E OR TM-D700A (G)
(TRANSPORTER) CONFIGURATION
1 Configure the TH-D72A/E, TM-D710A/E, or TM-D700A
as a “Transporter” and connect all necessary cables to
the TS-990S transceiver.
2 Select a frequency (HF/ 50 MHz band) on the TS-990S
transceiver.
3 On the TS-990S, be sure that "9600 [bps]" has been
configured in Menu 7-00, "Baud Rate (COM Port)".
Refer to "SELECTING THE BAUD RATE OF THE COM/
USB (REAR PANEL) PORT" for the configuration
method. {page 16-10}
4 On the TS-990S, be sure that "Off" has been
configured in Advanced Menu 24, "MSQ/ PKS Pin
Assignment (COM Connector)".
5 Select the same and common communication
parameters as those configured for the TH-D72A/E,
TM-D710A/E, or TM-D700 transceiver.
6 Configure and start the Transporter mode on the TH-
D72A/E, TM-D710A/E, or TM-D700A transceiver.
Note:
◆ For the SKY COMMAND SYSTEM II operation, use the main band
for operation. You cannot control the operation in the sub band.
◆ To connect the TH-D72A/E, TM-D710A/E, or TM-D700A
transceiver to TS-990S, you need three cables customized by
you. Refer to the instruction manual supplied with the respective
transceiver for the wiring diagram.
◆ On the TS-990S, SKY COMMAND SYSTEM II cannot control the
Dual Channel Memory. You can do only Simplex operation using
Memory Channel.
◆ The transceiver power cannot be turned ON or OFF while in
Standby State Low Power Consumption.
◆ Each time a "Commander" toggles between VFO A and VFO B,
TS-990S also toggles the operating data between the main band
and sub band.
Even if the "Commander" toggles between VFO A and VFO B
resulting to swap the operating data of the "Commander", "VFO A"
always appears on the display of the "Commander".
In Split operation, VFO A is used for reception and VFO B is used
for transmission.
CONTROLLING THE LINEAR AMPLIFIER
While a linear amplifier is in use, you can control the linear
amplifier control signal and transmission delay.
CONTROLLING THE LINEAR AMPLIFIER FOR
OPERATION IN THE HF BAND
To connect the linear amplifier to the REMOTE connector
on the rear panel and to operate in the HF band, you can
configure to enable or disable the control signal state and
the transmission delay time.
Refer to "INSTALLING AND CONNECTING THE
TRANSCEIVER" for the details of connector. {page 1-10}
[F1]~[F7]
[MENU]
F[ADV]
1 Press [ADV.] (F) from the Menu screen to open the
Advanced Menu screen.
2 Access Advanced Menu 11, "Linear Amplifier Control
(HF MHz Band)".
3 Press [SELECT] (F4) to allow editing of the parameter
box.
4 Press [-] (F4) or [+] (F5), or rotate the MULTI/CH
control to select the linear amplifier control method.
The available parameters are as follows: The default is "Off".
Off, Active High, Active High + Relay Control, Active High
+ Relay & TX Delay Ctrl, Active Low, and Active Low + TX
Delay Control
5 Press [ ] (F1).
6 Press [MENU] to exit.