TK-5210
(
G
)
7
REALIGNMENT
• Cloning is only possible when transceivers are using
hardware version 3.0.
• You can not clone if the password (overwrite password)
is programmed to the target.
• You can not clone if the checksum in the Network File
area of the source transceiver and the target transceiver
is different.
• ”Model Name and Market Code” must be same to clone
the transceiver. However, it may be unable to clone the
transceiver depending on the enhanced features set-
tings. (Refer to the FPU for the enhanced features de-
tails.)
• Under certain conditions, clone mode cannot be acti-
vated even if the clone mode of the source transceiver,
using Hardware Version 3.0, is set to enable. Refer to
the FPU for more details.
8. Self Programming Mode
(K2, K3 and K7 models only)
Write mode for frequency data and signaling etc. To be
used ONLY by the authorized service person maintaining
the user's equipment.
The following setup items in the channels programmed
by the FPU can be changed using the “Self-programming”
mode. The addition of new channel and the deletion of
channel that has already been programmed by the FPU can-
not be performed using the self-programming mode.
• RX
frequency
• TX
frequency
• Channel
type
• TX mode (When the channel type is selected “MIXED”.)
• Channel spacing (When the channel type is selected
“ANALOG” ro “MIXED”.)
• RX
signaling
• TX
signaling
• RX
NAC
• TX
NAC
• Talkgroup list number
Note:
The personality will be also changed when the above-
mentioned items is changed. (Refer to the FPU for the
personality details.)
Key guide on the “INPUT PASSWORD” display.
• CNF ([A] key): The password confi rmation
• DEL ([B] key): Delete the least digit from the current
password number (Press and hold to delete all password
numbers)
• SET ([D] key): Determine the least digit of the password
number
8-1. Enter to the self programming mode
Press and hold the [Side2] and [PTT] keys while turning
the transceiver power ON and then release the [PTT] key
fi rst. Ignoring whether the Read authorization password is
set or not, “INPUT PASSWORD” appears, then release the
[Side2] key.
If the Read authorization password is not set to the
transceiver, “SELF PROG MODE” is displayed on the LCD
when the [A] key is pressed while “INPUT PASSWORD” is
displayed.
If the password is set to the transceiver, “SELF PROG
MODE” is displayed on the LCD when you enter the correct
password while “INPUT PASSWORD” is displayed.
For the password input method, see “7.Clone Mode”
step 3 described on page 6.
Note :
This mode (self programming mode) cannot be set when
it has been disabled with the FPU.
8-2. Data Writing
Before moving to the next Zone/Channel, “KEEP THIS
CHANGE?” appears on the LCD, if you select ”YES”, the
new data is written to memory. IF you select “NO”, the
new data will not be written; the new data will be erased.
• The setup items for self programming mode are as follows.
No.
Setup item
Display
Remarks
1
Select
Zone/Channel
ZONE [***] -CH ***
ZONE *** -CH [***]
Zone: 1~100
[K7 model only Zone: 1~32, CH: 1~128]
CH: 1~512
2
RX frequency
RX Freq
Receive frequency
3
TX frequency
TX Freq
Transmit frequency
4
Channel type
CH Type
ANALOG/P25/MIXED
5
TX mode
TX Mode
ANALOG/P25
6
Channel spacing
CH Space
25.0kHz/12.5kHz (When the Channel type is selected “ANALOG” or “MIXED”.)
P25 12.5kHz
7
RX Signaling
RX Sig
Receive QT/DQT
8
TX Signaling
TX Sig
Transmit QT/DQT
9
RX NAC
RX NAC ***
000~FFF (Hexadecimal) Note: “F7F” cannot be set.
10
TX NAC
TX NAC ***
000~FFF (Hexadecimal) Note: “F7E” and “F7F” cannot be set.
11
Talkgroup list number
TG List No. ***
1~250