![background image](http://html.mh-extra.com/html/kenwood/tk-5210/tk-5210_service-manual_191525006.webp)
TK-5210
(
G
)
6
REALIGNMENT
Note:
• This mode cannot be entered if the Firmware Program-
ming mode is set to Disable in the Programming soft-
ware.
• The text message are displayed for K2, K3 and K7 mod-
els only.
• These transceivers use fi rmware versions G5.10 or later.
When using fi rmware versions earlier than version G5.10
a “Check connection” error message will appear on the
LCD. Firmware versions earlier than version G5.10 will
not write to the transceiver.
6-4. Checksum display
1. If you press the [Side1] switch (top of left side) while
“PROGRAM FIRMWARE” is displayed, the checksum
is calculated, and a result is displayed. If you press the
[Side1] switch again while the checksum is displayed,
“PROGRAM FIRMWARE” is redisplayed.
Note:
• Normally, write in the high-speed mode.
• The text message are displayed for K2, K3 and K7 mod-
els only.
7. Clone Mode (K2, K3 and K7 models only)
Programming data can be transferred from one trans-
ceiver to another by connecting them via their external uni-
versal connectors. The operation is as follows (the transmit
transceiver is the source and the receive transceiver is a
target).
The following data cannot be cloned.
• Tuning
data
• Embedded message with password
• Model name data
• ESN (Electronic Serial Number) data
• Network
fi le data (P25)
Key guide on the “INPUT PASSWORD” display.
• CNF ([A] key): The password confi rmation
• DEL ([B] key): Delete the least digit from the current
password number (Press and hold to delete all password
numbers)
• SET ([D] key): Determine the least digit of the password
number
1. Press and hold the [Side2] and [PTT] keys while turning
the transceiver power ON and then release the [Side2]
key fi rst. If the Read authorization password is set to the
transceiver, the transceiver displays “CLONE LOCK”. If
the password is not set, the transceiver displays “CLONE
MODE”.
2. When you enter the correct password, and “CLONE
MODE” is displayed, the transceiver can be used as the
cloning source. The following describes how to enter the
password.
3.
• How to enter the password using the keypad (K3
model only);
If the [D] key is pressed while “CLONE LOCK” is dis-
played, the Read authorization password input screen
(INPUT PASSWORD) is displayed.If one of keys 0 to 9
is pressed while “INPUT PASSWORD” is displayed, the
pressed number is displayed on the LCD. Each press of
the key shifts the display in order to the left. When you
enter the password and press the [A] or [*] key, “CLONE
MODE” is displayed if the entered password is correct.
If the password is incorrect, “CLONE LOCK” is redis-
played.
• How to enter the password using the [Side2] and
[Side3] keys (K2, K3 and K7 models);
If the [D] key is pressed while “CLONE LOCK” is dis-
played, the Read authorization password input screen
(INPUT PASSWORD) is displayed. If the [Side2] key or
[Side3] key is pressed while “INPUT PASSWORD” is
displayed, the number (0 to 9) fl ashes on the LCD. When
you press the [D] key, the currently selected number
is determined. If you press the [A] key after entering
the password in this procedure, “CLONE MODE” is
displayed if the entered password is correct. If the pass-
word is incorrect, “CLONE LOCK” is redisplayed.
4. Power ON the target transceiver.
5. Connect the cloning cable (part No. E30-3325-05) to the
universal connectors on the source and target.
6. Press the [Side1] or [A] key on the source while the
source displays “CLONE MODE”. The data of the source
is sent to the target. While the target is receiving the
data, “PROGRAM” is displayed. When cloning of data
is completed, the source displays “END”, and the target
automatically operates in the User mode. The target can
then be operated by the same program as the source.
7. The other target can be continuously cloned. When the
[Side1] or [A] key on the source is pressed while the
source displays “END”, the source displays “CLONE
MODE”. Carry out the operation in step 4 to 6.
8. To return to “User mode” on the source transceiver, you
must first turn the transceiver power off and then on
again.
Cloning cable
(E30-3325-05)
Fig. 2
Note:
• You can not clone transceivers using hardware version 1.0
or 2.0.