5
TK-390
2-9. Temporarily Delete/Add
It is possible to delete or add channel temporarily during
scan. When scan stops on unnecessary channel for ex-
ample by interference of the other party, activate the delete/
add function (for example press the key), then that channel
is deleted temporarily and scan re-start immediately.
When you would like to add the deleted channel tempo-
rarily to scan sequence, select the desired (deleted) channel
during scan, activate the delete/add function (for example
press the key) before scan re-start.
That channel is added temporarily to scan sequence. The
temporary deleted or added channels are returns to pre-set
delete/add, when the transceiver exits from scan mode.
3. Optional Features
You can use these features using the programming soft-
ware (KPG-38D).
3-1. Alphanumeric Display (Group/Channel Name)
The programming software (KPG-38D) enables you to set
the alphanumeric display for group/channel name. The total
text size of group and channel name are 7-digits.
For example, If you set 2-digits for group name, then you
can use 5-digits for channel name. The characters can be
used as shown in Figure 1.
3-2. Beep Tones
The beep tones (power on tone, control tone, warning
tone, alert tone) are individually programmable to the fixed
level 0 to 31 or follow the mechanical volume position.
3-3. Minimum Volume
The minimum volume is programmable (0 to 31). The
transceiver remains the minimum volume level however the
mechanical volume position is set to zero.
A B C D E
F G H
I
J K
L M N O P Q R
S T U V W X Y Z
1
2
3
4
5
6
7
8
9
0
-
All on
Fig. 1
3-4. Squelch Threshold Level
Squelch threshold level value.
0 (Most loose)~15 (Most tight)
3-5. BCL (Busy Channel Lockout) Override
You can transmit in spite of Busy Channel Lockout situa-
tion. For example : To make an emergency voice call.
To transmit under busy channel lockout situation, press
PTT once more within approx. 500ms after the PTT release.
3-6. Selective Call Alert LED
You can select whether or not the LED on the transceiver
flashes in an orange color when Selective call was occurred.
3-7. Battery Warning
This transceiver has battery warning feature. If the low
voltage is detected during transmission, the transceiver
warns it by flashing red “LED”.
Then more low voltage is detected during transmission,
the transceiver stops transmission and warns it by flashing
red “LED” and beep.
Please notice “standard” for the battery exchange,
charging time by flashing red LED and beep.
3-8. Busy LED
You can program the enable or disable the busy “LED”
function when a carrier is detected. “Disable” saves battery
life.
3-9. TX LED
You can program the enable or disable the transmission
“LED” function.
3-10. 2-Digit 7-Segment Display
You can use 2-digit 7-segment the display to display the
channel number or group number. It is useful when the
main (7-digit 13-segment) display indicates group or channel
name.
3-11. Invert Display
Main (7-digit 13-segment) display and sub (2-digit 7-seg-
ment) display can be programmed to invert display.
It is easy to read the display when the operator sus-
pended the transceiver on a waste belt. The operator also
can change the display between normal and invert using
key. Refer the invert display function of key function.
3-12. Clear to Transpond
The transceiver waits the transpond of 2-Tone/DTMF if
channel is busy until channel open. This feature prevents
the interference to other party.
3-13. External Speaker
It can be selected if the receive sound is made by SP-Mic
SP or the main body SP at a SP-Mic mount.
3-14. Noise Cancelling MIC
Enable or disable the noise cancelling function of the in-
ternal microphone. It is not valid for the external SP/MIC.
OPERATING FEATURES
